Benzenesulfinic Acid Sodium Salt: A Complete Guide for Industrial Buyers

Editor:Jinli Chemical │ Release Time:2026-11-20 

Benzenesulfinic acid sodium salt (sodium benzenesulfinate, PhSO2Na) is easy to buy and easy to misuse. Most failed batches trace back to a few avoidable things: assuming 100% active content, ignoring water and inorganic salts, or choosing the wrong form of the reagent.

What You Are Actually Buying

The compound is a white crystalline powder. Supplier databases list a melting point above 300 °C and an EINECS number of 212-842-8 (ChemicalBook; Sigma-Aldrich). A hydrated form is also catalogued, so always confirm on the certificate of analysis whether your lot is anhydrous or a hydrate, because the molar mass differs.

ItemValue
CAS number873-55-2
FormulaC6H5NaO2S (written C6H5SO2Na)
Molecular weight (anhydrous)164.16 g/mol
AppearanceWhite crystalline powder
Common synonymsSodium benzenesulfinate; sodium phenylsulfinate; benzenesulfinic acid sodium salt

Reading the Specification Like a Chemist

The specification on the Jinli Chemical benzenesulfinic acid sodium salt product page is a useful checklist. The right-hand column below is our interpretation of why each line matters in practice, not a statement from the product page.

Check pointSpecificationWhy it matters in use
Purity98% minSets the correction factor when weighing for exact stoichiometry.
pH7–10Mildly basic to neutral; matters if your substrate or catalyst is acid or base sensitive.
2% water solutionClearA fast incoming test: haze suggests insoluble matter.
Water1.0% maxAffects weighing accuracy and any water-sensitive coupling partner.
Sodium chloride1.0% maxInert inorganic salt; likely a carry-over from sulfonyl chloride–based preparation.
Sodium sulfate1.0% maxInert diluent; can matter in electrochemical or ion-sensitive work.
Sodium carbonate0.05% maxTight limit; relevant for pH-controlled steps.
Heavy metals10 ppm maxWorth watching if you run metal-catalyzed couplings or pharmaceutical steps.

A weighing example. For a 10 mmol reaction, pure PhSO2Na is 1.64 g (10 × 164.16 mg). If the lot is 98% pure on an as-received basis, weigh about 1.68 g. The difference is only 2%, but in a reaction where the sulfinate is the limiting reagent, that is the margin between a clean result and an unexplained shortfall. Check whether the stated purity is on an as-received or dried basis before you correct for water as well.

Choosing a Reaction Route

Sodium sulfinates behave as sulfonylating, sulfenylating or sulfinylating reagents depending on conditions, and form S–S, N–S and C–S bonds (Reddy and Kumari, RSC Advances, 2021). They are also described as more stable and less moisture-sensitive than sulfonyl chlorides (Aziz et al., Org. Biomol. Chem., 2014), which is a practical reason to prefer them when storage and handling convenience matter. The routes most relevant to PhSO2Na are summarized below.

GoalTypical partnerPractical note
Alkyl or benzyl sulfonesOrganic halidesReported in higher alcohol or diol solvents (Kauffman, J. Chem. Eng. Data, 1969, via Sigma-Aldrich). Sulfinate is an ambident nucleophile, so check for sulfinate ester by-products.
Aryl sulfonesBoronic acids, copper catalystCatalyst loading and ligand choice drive results; trace metals in the reagent are worth tracking.
Vinyl sulfonesVicinal dibromidesReported by Sigma-Aldrich as a use of this reagent.
HeterocyclesResin-bound or domino partnersUsed as a traceless linker for pyrazolines, isoxazolines and imidazoles (Org. Lett., 2003; J. Comb. Chem., 2005) and in a copper-catalyzed domino synthesis of 4-benzenesulfonyl isoxazoles (J. Org. Chem., 2020).

Some suppliers also list polymer uses, such as adhesion enhancement and modification of polyamide, epoxy and phenolic resins (ChemicalBook). Treat these as application leads to validate in your own formulation rather than guaranteed performance.

A Short Incoming-Inspection Routine

  1. Compare the certificate of analysis against the specification table above, including water and salt content.
  2. Dissolve a small sample at 2% in water and look for clarity.
  3. Check the pH of that solution against the 7–10 range.
  4. Run a small test reaction before committing a large batch, especially if you are switching suppliers.
  5. Retain a sample from each lot so a later problem can be traced back.

Troubleshooting

SymptomLikely causes to check
Yield consistently a few percent lowWeighing without purity or water correction; hydrate versus anhydrous mix-up.
Hazy stock solutionInsoluble impurities, or poor-quality water; compare against the clear 2% solution specification.
Catalyst seems to die earlyTrace metals, moisture, or oxygen exposure; test with a lot of known performance.
Unexpected by-product in halide reactionsCompeting O-alkylation of the ambident sulfinate; revisit solvent and temperature.
Lot-to-lot variationDifferences in salt content or moisture within the allowed limits; adjust the weighing correction per lot.

Handling and Storage

Supplier safety data lists the compound with GHS07 (irritant or harmful) classification and a German water hazard class of 1 (Sigma-Aldrich; ChemicalBook). In practice: wear gloves, safety glasses and a lab coat, avoid generating dust, and keep the container tightly closed in a cool, dry place away from strong oxidizers. Always read the current safety data sheet for your specific lot before use. This article is general guidance and does not replace it.

Related Intermediates

Teams that use PhSO2Na often need neighbouring sulfinate and sulfonyl products on the same line. These are available from the Intermediates Series, and the full range is on the product catalog page.

ProductRoleKey listed data
Benzenesulfinic acid sodium saltSulfinate reagent98% min, water 1.0% max
Sodium p-toluenesulfinate (CAS 824-79-3)Methyl-substituted analogue98% grade, pH 7.0–9.0, water 1.0% max
Benzenesulfonyl chloride (CAS 98-09-9)Sulfonylating precursor; reacts with water99% min, water 0.1% max
P-Toluenesulfonyl chloride (PTSC)Related sulfonyl chlorideSee product page
Benzenesulfinic acid zinc salt (BM, ZBS)Zinc sulfinate98% min, melting point 218±3 °C

This article is for general technical information. Verify specifications and safety data with the supplier for your specific lot before use.

Benzenesulfinic Acid Sodium Salt